Video

AdvancedTomato on the Linksys EA6700

Install AdvancedTomato firmware onto the Cisco Linksys EA6700

If you’re interested, you can read some background informaiton on how I came about AdvancedTomato.

15 minute upgrade video, step by step in real time.

Disclaimer

When doing things on the firmware level there is always a possibility that something might go wrong and your router becomes bricked.

The long guide (for beginners)

  1. Download the AdvancedTomato firmware from the download page.

  2. Download the old stock firmware, FW_EA67001.1.40.166281prod.img from Linksys.

  3. Save anything you need internet for before you lose it, if this is the router you use for the internet.

  4. IMPORTANT: If your router is running firmware build version 172250 or higher you’ll have to downgrade to build 166281, as you can’t upgrade to AT from the newer versions. To do this follow the guide here.

  5. Check your router is running on build 166281.

    1. Login to the remote web interface. (default password is admin)

    2. Go to the Connectivity page, under “Firmware Update” it’ll show your build version.

      e.g. (Current Version: 1.1.40.166281) the bold part is the build version.

  6. Make sure to have nothing else plugged into the router but the one network cable you’ve got plugged into your computer and the routers Ethernet 1 port.

  7. Wipe the device’s settings; go to Troubleshooting then the Diagnostics tab, then it’s under the “Factory reset” link, “Reset”, or hold the reset pin for 30 seconds, then release and you should see all the network port lights, light up.

    Once the device is back up follow these steps;

    1. Tick that you’ve read and accepted the License Terms.

    2. Also tick “I want to skip Setup and configure my router manually”, click next, wait ~20 seconds while it figures out you have no internet, then click login.

    3. Login (default password is admin).

    4. Go to the Connectivity page, under “Firmware Update”

    5. Click on Choose File under the “Manual” heading.

    6. Select the old stock Linksys firmware image, FW_EA67001.1.40.166281prod.img

    7. Click Start and Yes.

  8. Once the device finishes its “upgrade” (at least 3 mins), log back in and upload the new AT firmware.

  9. Wait about 5 mins, then go to http://192.168.1.1/, if nothing loads, take the power out and plug it back in (reboot it), wait 5 mins, try the above link, wait a few seconds and the AT web UI should load.

    If it doesn’t, wait another 5 mins, if still nothing then abort, reset it (unplug power from router, push the reset pin, plug power back in, hold reset pin for 45 seconds, then let go, wait 5 mins and the stock firmware should be back), then start again from step 1.

    If you end up back on the stock Linksys firmware, start again and redo all the steps and check what IPs are assigned on your computer while the upgrades are happening (see below).

  10. Login, the default username/password is admin/admin.

  11. Finally “Erase all data in NVRAM memory (thorough)” in Administration > Configuration under “Restore Default Configuration”.

    This is very important, if you skip erasing the NVRAM the new firmware won’t hold.

  12. Click OK to the confirmation, and it’ll reboot. (~2mins)

  13. Login, go to Administration -> Scripts and paste in the 3 lines below on both the Init and Shutdown tabs, and click Save. This helps keep your router stable. (more info in the comments)

    for line in $(nvram show | grep =$); do var=${line%*=}; nvram unset $var;
    done
    nvram commit
    
  14. Finally, change the default password.

  15. You’re done!

The quick guide (for advanced users)

  1. From the official Linksys firmware make sure you’re running on build 166281.

  2. Wipe the device’s settings.

  3. After reboot, “upgrade” to the official firmware, build 166281.

  4. Upgrade to AdvancedTomato firmware.

  5. “Erase all data in NVRAM memory (thorough)” in Administration > Configuration.

  6. Add the 3 lines from the link below to both Init and Shutdown tabs in
    Administration > Scripts

    for line in $(nvram show | grep =$); do var=${line%*=}; nvram unset $var;
    done
    nvram commit
    

Troubleshooting

  • Read the comments for help if your WiFi goes down after a few days.

  • If after flashing AT and you reboot the router and end up back on the official Linksys firmware, try the steps again, but flash the official firmware twice, not just once, then flash AT and erase the NVRAM.

    Also check out chanz’s comment as he talks about it, as well as other comments.

Old firmware mirror

A mirror of the 166281 firmware has been hosted on my server in case Linksys takes down the link one day.

30/30/30 reset?

According to jago75, the 30/30/30 reset has no effect on ARM-based routers like the EA6700.

Why the double firmware install?

The steps for installing the Tomato firmware onto the EA6700 router are a little different than that of normal routers. It has 2 locations where it stores firmware, and if you try to install AdvancedTomato as per normal, it will just reboot back to the stock Linksys firmware.

This is why we first “upgrade” to the stock firmware (into the first location), then again with AdvancedTomato, into the second location, which is what it runs from by default. (at least this is my understanding)

Disbale all LED lights (except the Linksys logo)

In the Administration > Scripts page, put the following into the Init tab, save, and reboot.

sleep 10
et robowr 0x0 0x18 0x0
et robowr 0x0 0x1a 0x0

Some acronyms

AT = AdvancedTomato
AIO = All In One (has everything)
VPN = A cut-down version of the firmware with specific VPN support
OFW = Official Firmware, e.g. what originally come with the device
CFW = Custom Firmware, e.g. what we’re putting on the router (Tomato, DD-WRT, OpenWrt etc)
NIC = Network Interface Controller (the things where you plug the network cables into)

Disclaimer

I am by no means an expert in flashing firmware, only done it a few times, first a Netgear router (DD-WRT), then a Linksys (DD-WRT), and now this Linksys router (AdvancedTomato), just thought I’d share this as I couldn’t find anything online on this specific router and Tomato based firmware, and didn’t have much success with my initial attempts.

Alternative name

Cisco Linksys Smart Wi-Fi Router AC 1750 HD Video Pro

Feel free to leave any feedback in the comments.

  • Orbital

    Thanks! This helped me a bit.

    • adriel

      No problem, glad I could help.

  • val bete

    Thank you!

  • joe A.

    I used this method on my EA6500v2 as well. Now I’ve got a dual core 800 mhz 256 Mb Shibby router I purchased for $56 on Amazon. I’m very pleased!

    • adriel

      Cool, glad it worked with the EA6500v2 as well!

  • joe A.

    I did use the EA6500 firmware from Linksys and Shibby I should add.

  • Anon

    Do not 30/30/30 cycled your Linksys EA6xxx after flashing or then it may already be too late and it’s bricked (erased nvram)

  • Stefan

    Nice guide. I have the EA6700 and managed to boot in to advancedtomato (AT) a couple of weeks ago. I did not managed with the procedure right away. It took a couple of retries before AT was booting.

    Yesterday I upgraded to the 132 version and tried to get virtual wireless interfaces which use a VPN account to connect to internet. I did not succeed… but that is another problem for another day.

    In the process I managed to get AT to lose one of the wireless interfaces (not the virtual one). Rebooting did not help. As a last attempt I did a hard reset. This of course flashed back the Linksys stock firmware. I have now tried to flash AT 6-7 times but fail every time.

    Steps taken.
    1. Factory reset from Linksys fw.
    2. Flash Linksys 1.1.40
    3. Flash AT 3.0/3.1 and standard tomato 1.29.

    After this the router reboots and then i wait at least 5 minutes. Nothing happens and I eventually power cycle the router. The router never boot up normally efter this, neither AT or Linksys. I have to do a hard reset to get back to Linksys fw.

    So, I need some advice. First thing I want to test is to use an older Linksys firmware to test with, but I can not find any. If that does not work I think I am out of ideas…

    Any ideas or tips would be welcome… I really hate Linksys fw which is very limited.

  • adriel

    Have you tried flashing linksys onto it twice with the latest linksys version, maybe that will help clear out any bugs… Sorry I don’t really have much more.

    You’d probably have more luck asking on a tomato forum for help.

  • Stefan

    I actually got it working again… Unfortunately I don’t know what made it work

    I have also figured out what was making my router setting to drop the wireless interface. It was the famous 50% nvram bug. When adding the certificate for the vpn-client setting nvram used more then 50% of nvram.

    To restore from this situation I erase all data in nvram instead of restoring default values. After that I can import a configuration and reboot again.

    I am now struggling to get around this problem. I have read on some page you can point out the ca.crt file instead. I have stored it on /jffs/ but have not figured out how to get openssl (?) to read it from there.

    I will eventually move on to a tomato forum and ask for help. But that is not as fun 😉 I started to write on this blog since this is the place where I found out how to flash my router.

  • adriel

    Thanks for the update Stefan!
    Hope you figure out your cert problem.

    • Daniel Andersson

      Hi, how do i revert my router to the original Linksys firmware? I´ve tried the 30/30/30 method and i always ends up in Advanced Tomato again. I really need to get back to stock firmware.

      • https://adriel.co.nz Adriel

        Not 100% on this, but pretty sure all you need to do is select the Linksys firmware image (that you downloaded from Linksys) from in AT in the Upgrade menu, select “After flashing, erase all data in NVRAM memory”, then click the Upgrade button and you should end up back on stock firmware.

  • Danijel

    I am having the same problem with my EA6700. After some time 2.4Ghz is not broadcasted and shown in options. Only see 5Ghz network but it doesn’t seem to be broadcasted as I don’t see it in my phone. I cleared NVRAM after install and I know it will bring back my wifi networks but that means I will have to manually set everything back from the start as restoring settings will bring wifi issue back.
    Is there any other solution?

    • adriel

      Are you running the latest version? “3.1-134”, was just updated a week ago, maybe that’ll fix it.

      My EA6700 has been up (without a restart) for 40 days on “1.28.0000 -3.1-132 K26ARM USB AIO-64K” and I’ve not had any 2.4 or 5 GHz issues, just upgrading to 3.1-134 today.

  • Kim

    I’m having all sorts of issues getting AT onto this recently purchased router.

    I had it running once following the guide, but like Danijel my 2.4GHz dissappeared, so I factory reset it back to the LS firmware.

    Now I can not get AT to work, it flashes but when booting eventually pings stop and there is no contact. I’ve tried both AT 1.32 and 1.35.

    The only cure is to factory reset back to the LS firmware

  • Sergio

    Same issue on ea6500v2; lost my 2.4Ghz when power cycling. Restoring backup results in issue returning, so I have to manually reconfigure everything. Using latest build 3.1-135

  • Meir

    Never managed to flash my ea-6700.

    did flash twice,
    once with LS firmware
    and second time with the AT firmware (135 and 134)

    AT firmware always starts unidentified, no DHCP, nothing is alive,
    after booting, router reverts back to LS firmware.

    Did someone bumped into this ?
    any advice?

    • adriel

      Maybe try AT firmware v137.

      Also, try flashing the AT firmware once more with the same AT image once you’ve got AT on it. That should make it stick.
      And did you try “Erase all data in NVRAM memory (thorough)” in Administration > Configuration.” once you’ve got AT flashed? It might fix your DHCP etc issues.

      Let me know how it goes.

  • Paulo Cunha

    I am having the same issue with lost 2.4. The only way to get it back is to reconfigure everything. If i restore a last working backup it will bring the problem back. Any light?

  • Ronald

    I also have the lost 2.4. If I do nvram erase it will come back temporarily, until i reboot it and then, eth1 becomes 5GHz. I am not hitting 32k limit either (I tried to delete nvram down to the limit but the problem persisted)

    The WL interfaces actually show up when I login via SSH. However, the SSID isn’t actually available and cannot be seen on the web admin.

  • Ronald

    I find that the 2.4G issue was related to the 32k bug issue. If I kept nvram usage belog 32KB, it can reboot without losing WiFi. However I have another issue. If I reboot it a couple of times it will automatically go back to stock. It happens even if I flash it 2 or 3 times. I switch off the router at night and the same issue is found if I use the shutdown function or directly power off.

    Do you have this issue?

    • adriel

      Hmm, no don’t have the reboot issue, though I never shutdown or turn off my router, except for maybe once when there was a powercut and the UPS died. Think once it did go back to stock though, when I was messing with settings/restores, but since then it reboots fine, and always stays on Advanced Tomato. Check that you’ve done the erase all the NVRAM option after putting AT on it, this may help. (though reading your previous comment, which was stuck in spam for some reason, it seems you have already done this, so not sure what else you could try).

      If you do find the solution please do leave a comment here.

      edit:
      Just thinking, did you try flashing the stock firmware, then AT? Like when you shut down the router and turn it back on, and it’s back to stock, don’t go straight to AT, first flash the stock firmware even though you’re already on stock, then flash AT.

      Though I’m thinking it shouldn’t matter whether you flash AT twice or stock + AT, but worth a try.

  • Ronald

    I did that too but the problem still persists.

    I even tried to flash old stock firmware, then new stock firmware, then AT, nvram erase, AT, AT .. But it went back to stock again.

    It looks as if in AT, flashing goes to current partition instead of backup.

    In any case, thank you for the suggestion

  • chanz

    #4 – you’re probably pointing to:
    – menu Troubleshooting
    – tab Diagnostics
    – under FactoryReset button/link “Reset”

  • chanz

    Like some other ppl – I am also no longer able to flash any AT to ea6700. I’ve tried even older OFW – FW_EA6700_1.1.40.166281_prod (or current FW_EA6700_1.1.40.176451_prod), also older AT tomato-EA6700-AT-ARM-3.1-132-AIO-64K (or latest tomato-EA6700-AT-ARM-3.3-138-AIO-64K). It looks to me, like LS did some changes – 2nd flash with AT it always start respond to ping, but then it stops and no matter whether 1m or 5 or 25m of waiting – it never goes up. It doesn’t react on reset button – only unplug of power… but it always returns OFW back.
    How it start:
    Yes, I was affected by NVRAM issue. I upgraded from mentioned older AT to latest and run it for weeks. Afterwards i performed unplug power & Wifi got mad (interfaces had wrong binding of MAC & didn’t work at all). So I performed one of the reset – (AFAIR not throughout – but not sure now). This returned OFW back & since then I am without AT :-/

  • chanz

    WOW – I am one from many ppl who experienced an issue which prevents me from flashing AT. So eventually works for me – but I am not sure for how long (survived reboot/poweroff). I read a tons of topics on various forums – the majority ppl didn’t believe those who complain.
    Symptoms are pretty tricky – inability to flash , or sometimes loosing AT flash after reboot/power-off the EA6700 (or EA6500v2).
    The trick which worked for me eventually is:
    1. upgrade to ofw
    2. upgrade to ofw
    3. upgrade to ofw
    4. upgrade to tomato.
    At the beginning indeed set everything to default 192.168.1.1 (also tried with my own address, but also only with the latest ofw {see below}).

    I didn’t succeed with latest ofw – FW_EA6700_1.1.40.176451_prod.img at all – I did it ~10times multiply 2 flashes as described in article. Afterwards I tried exactly the same with previous ofw – FW_EA6700_1.1.40.166281_prod.img – which worked. So 3 times in a row with ofw and then AT – tomato-EA6700-AT-ARM-3.4-138-AIO-64K.trx.img – like a charm!

    source:
    http://www.linksysinfo.org/index.php?threads/ea6700-with-2-flash-partitions-goes-back-to-stock-firmware-after-reboot.72989/#post-281539

  • Kbuggenhout

    for some reason the nvram variable partialboots=x is not reset with successfull boot, and the default maxpartialboots is set to 3 so after 3 boots it falls back to stock no matter what you do.

    to solve this..

    make sure that you reset the partialboots value to 1 every boot when it reaches the end of configuration ( last item in init.d) do a nvram set partialboots=1, do not forget nvram commit after that.. to make it stick.

    a bit lost in the code.. as it doesnt have an init.. inittab, rc.d or init.d…

    but you can always type the command in the administration page/command…

  • Kbuggenhout

    uhmm.. in administration scripts.. in the init field just add

    –cut here–
    nvram set partialboots=1
    nvram commit
    –cute here–

  • https://adriel.co.nz/blog/2015/10/06/advancedtomato-on-the-linksys-ea6700/ Konstantin

    Hello all
    + One problem with the latest firmware EA6700-AT-ARM-3.4-138-AIO-64K.trx after upgrade, after the upgrade my EA6700 is lost 2.4G Range, and unconnected pppoe connection – writes “connecting” or “renewing” in status connection and even get ip address for the passage of the authorization

    • Ronald

      I had the first problem too (2.4G) which can be resolved by cleaning nvram until it uses less than 32k.
      I didn’t use PPPoE so I cannot help on this part. However, it is likely the same problem.

      What I did was quite complex. You can adapt to your needs.
      1. Login via ethernet, make all the necessary changes
      2. Before any reboot, make a nvram dump
      3. Download it on your computer and clean up unnecessary settings
      4. Erase nvram and load the content of that text file into Tomato (I did it with the help of a small shell script)

      (The nvram includes some sensitive data like router password, SSH hostkeys and a couple of other things, so don’t share it on the net)

  • Eri

    Has any one tried wireless bridge/repeater mode? I want to use its LAN port while it is being used as a wireless bridge, does that work? Thanks in advance!

  • Hans

    I have tried anything written above, the correct steps and when that not worked, the steps of Chanz.
    But it’s not working for me, it’s still booting in Linksys mode every time.
    I used what Chanz said, FW_EA6700_1.1.40.166281_prod.img and EA6700-AT-ARM-3.4-138-AIO-64K.trx.img
    Any other suggestion?

  • Hef Wannabe

    I just started playing with AdvancedTomato, and I too have a Linksys EA6500v2. Today, I just flashed it to AT, and I spent WHOLE DAY screwing with it. I flashed it on one computer, then I moved the router to my cable modem location. Then, I tried to use it and wouldn’t work. So, I read what all you wonderful people have shared (like Chanz and others below), and it’s just damned frustrating. It wouldn’t give me DHCP from the router, then I rebooted and it went off-line. Then, trying to get it back on line was (like impossible). Then, I realized I couldn’t go to 192.168.1.1 (forever tried that with many reboots), but realized it went back to stock firmware and had some 10.x.x.x address.

    Okay, I’m not sure that this router is best for flashing with AT. Right? Could anyone suggest a fair-priced router that has good specs (more internals) versus wireless. I might just use my current one for wireless needs and find another for my central router. I love the hardware specs of the EA6500, but I don’t want to screw with it returning to stock after ANY & ALL POWER RESETS. That’s just too hard to deal with.

    Does it stay flashed forever if you get it flashed right? I mean … who creates a router that does stupid shit like this? We don’t live our lives just to become experts at flashing a router and wasting our lives dealing with it.

    I moved up from an ASUS RT-N16, and I flashed it with Tomato Shibby and it was PERFECT. PERFECT. No issues ever. Seriously, no issues ever. So, can I get this EA6500v2 like that, or am I just dreaming and wishing for clear skies and pink rainbows.

    Thanks, a student wanting to learn this more

    • https://adriel.co.nz Adriel

      Hey, yeah this routers hardware is amazing, and yes you can get to work rock solid with AT (latest version), mine can reboot just fine and still have AT on it, and ever since I added this bit of code https://cl.ly/38113Y0U4620 into both “Init” and “Shutdown” in the Administration/Scripts section my WiFi hasn’t disappeared on me. (Though I should note that I’ve turned off the 5GHz WiFi since it was causing interference with other wireless gear here, so don’t know if that helps too).

      I’ve also recently turned on QoS, rate limited some IPs and tweaked my max upload limit so my internet doesn’t grind to a halt every time someone’s phone tries to backup some photos, which has been working perfectly too.

      So the best advice I can give you is don’t give up, it’s possible. Read all the advice given here in the comments and try and re-try what’s suggested, I remember when I first tried to flash this router it was bit of a pain to get it to stick, so might just take a few tries before it works.

      The good thing about this router is that it’s like nearly impossible to brick, so doesn’t matter if you mess up, reset it and start again.

      • Hef Wannabe

        Adriel:
        Thank you for the words of encouragement. Yeah, it was a BITCH OF A DAY. I had been wanting to try and virtual TOMATO to a very old ShuttlePC. But Tomato is not x86. But, read about DD-WRT but didn’t seem to like the layout, then found AdvancedTomato and I was sold on it.

        But, actually, I was surprised that it was pretty easy to get on the device. However, it was a “little unclear” above (or, at least on my router) that I didn’t know where to find the RETURN TO FACTORY RESET or something, because I wasn’t familiar with Linksys GUI. It’s hidden, and I had to take it back to a certain version. It would not upgrade but only backgrade (if that’s a word). So, I did my best on above, but I might make suggestions when I do it again. If the person wants to change the steps, if I find anything different.

        But, yeah, it’s not as easy as it should be. Flashing on the Asus RT-N16 was very, very easy and instantly the new firmware stuck.

        So, your replies make me happy. I can’t wait until weekend, and I’ll give it a shot. It just feels good to be gaining confidence in this area, because I sure know that it is marketable.

        Sincerely, thanks, Hef …

    • https://adriel.co.nz Adriel

      Hey, sorry me again, just noticed I was missing a critical last step in my beginners instructions, the erasing NVRAM. Did you run the “Erase all data in NVRAM memory (thorough)” option after you flashed AT?

      • Hef Wannabe

        Adriel,
        First off, thanks for preparing this writeup. It really helped me understand the steps. I was so in love with my Asus RT-N16 and Tomato, but I heard (through grapevine) about AdvancedTomato; I looked at GUI and WOW — I got to have it on a router. Anyway …

        No, I did not flash the NVRAM. I didn’t know too.

        That was day before yesterday and whole day was frustrating monkeying with the EA6500v2. It should be easy, because it was with Asus RT-N16: very easy. One flashing and it has stayed with Tomato ever since. Even reboots and acts like NORMAL FIRMWEAR. That’s where I want to get with this AdvancedTomato.

        Anyway, I’ll try that when I get my day off and re-walk through the steps. Just makes me happy to find people with same device, where I can have a “tiny bit of help” to get there.

        Having a good router, is nice and very helpful. The normal firmware on Linksys really sucks. I’m dealing with fixed IPs like 10.x.x.x and everything in house had to be rebooted. Anyway, I can’t wait to get this AT (when I get time).

        Thanks.

        • https://adriel.co.nz Adriel

          I know the feeling, when I got this router and found AT, there was NOTHING on the internet about getting AT on it, so was a bit doubtful I’d get it working, but from the small bits of info I found I managed to figure it out.

          And yeah sorry about missing the NVRAM step, probably caused allot of headache for allot of people 🙁

          But yeah, let me know what works for you and I’ll amend the steps as needed.

          Also, when you’re on the Linksys firmware could you confirm my updated steps (step 4) are correct to reset the router?

          • Hef Wannabe

            Adriel:
            I’ll even go through the trouble of giving screenshots where it is clear. It’s STUPID PLACE how Linksys put that reset button or “go back to earlier firmware” ability in (like) 2 or 3 screens down. Whoever designed Linksys, sure didn’t plan on someone wanting to do that. They should have had the command on an ADMIN page or something like that. So, when I walk through it, I will go slow and grab the exact steps for you. Give me weekend, then I’ll get it to you happily. Thanks.

  • Darshit Dalal

    I tried all three ofw which are listed in this forum. None of them did work. It says invalid firmware, it will not work with this router. I purchased router 2 days ago from amazon. Did they change something recently in firmware?

  • Robert B.

    I was able to flash to my EA6700 the latest AT firmware. In benchmarking the 802.11ac 5ghz band though I found that I was only able to get a download speed of ~200mbps versus the stock OEM firmware where I would get 320mbps. Probably because the stock firmware can use hardware acceleration that isn’t available to AT or DD-WRT or other firmwares.

    I ended up reverting back to stock.

    • https://adriel.co.nz Adriel

      Hmm interesting, thanks for leaving the feedback!

      • blob_of_truth

        adriel which AT version are you running? Also did your router have an overheating problem?

        • https://adriel.co.nz Adriel

          I’m on “Tomato Firmware 1.28.0000 -3.4-140 K26ARM USB AIO-64K”
          No overheating issues yet, had it since Oct 2015. But I do have a fan on the base during summer when it gets hot here, around 30c (86f).

    • Konstantin Gess

      hello, you were flash to EA6700 – AT – ARM – 3.4-140 – AIO – 64k.trx ?? say for you everything works normally ?

  • Make Stuff

    In my humble opinion, none of the methods suggested in this blog post, or any of the comments below, are a true fix for 32K Nvram bug in the Linksys EA6700 router. They are all temporary fixes at best and will most likely lead to a loss of all DD-WRT or Tomato firmware settings and a reversion back to the router’s stock firmware at some point. The only real way to fix the 32K Nvram limitation issue permanently and avoid future issues is to flash the router’s CFE. If you are interested you can read the two following forum threads, which will explain everything:

    http://www.linksysinfo.org/index.php?threads/linksys-e2500-upgrading-to-ea6700-with-re6400-range-extender-on-tomato.73655/#post-289787

    http://www.linksysinfo.org/index.php?threads/asuswrt-merlin-xvortex-on-linksys-ea6900-supports-tomato-dd-wrt.71718/

  • Craig Fraser

    Hi, I have managed to upload this firmware to my EA6700 without any hassles, however am trying to configure it so that I can no longer use my Etisalat D Link DIR 850L (, which has been loaded with custom firmware from my provider: –
    https://www.reddit.com/r/dubai/comments/4rcu0i/guide_get_your_own_router_working_instead_of/
    http://www.expatforum.com/expats/dubai-expat-forum-expats-living-dubai/972866-etisalat-using-your-own-router-2.html

    However, the D-LInk makes use of VLAN ID 30, I have noticed that the AdvancedTomato firmware only seems to go up to 15….Is there any way this can be increased? Or is there a work around?

    I have yet to wrap my head around the whole VLAN ID and how to make it work, but I assume that you need to allocate the VLAN ID to the WAN port?

    The connection to the provider is PPPOE.

    I look forward to hearing from you.

    • Craig Fraser

      To just update, When in the Vlan page, when I try and tick the Wan Port Tagged checkbox, the router reboots but then fails to provide an IP and i cannot get back into the router, even after a restart. I think that the WAN Vlan ID needs to be tagged.

      • https://adriel.co.nz Adriel

        Yeah I’ve never had to deal with such high a high VLAN ID, and the last time I had to use a VLAN with PPPoE was with DD-WRT. Also may be worth mentioning that some ISP can turn off VLAN tagging, might be worth a try.

        Also I would try Google your issue something like “VLAN tagging higher than VLAN ID 15 in Tomato firmware”, since AdvanedTomato is just a skin on top of the Tomato firmware, so you should find a solution that way.

        Also I would turn on logging (Status -> Logs), and see if you get any useful details about why it might not be connecting (When you can get access to the router after a reboot)

        Aaalso here is the default settings for the VLAN page for reference.
        https://www.dropbox.com/s/jxoaoboy5ziyzhe/Screenshot%202017-09-09%2017.32.09.png?dl=0